Search results for "Thin layers"
showing 10 items of 38 documents
A Local Study of the Transport Mechanisms in MoS2 Layers for Magnetic Tunnel Junctions
2018
MoS2-based vertical spintronic devices have attracted an increasing interest thanks to theoretical predictions of large magnetoresistance signals. However, experimental performances are still far from expectations. Here, we carry out the local electrical characterization of thin MoS2 flakes in a Co/Al2O3/MoS2 structure through conductive tip AFM measurements. We show that thin MoS2 presents a metallic behavior with a strong lateral transport contribution that hinders the direct tunnelling through thin layers. Indeed, no resistance dependence is observed with the flake thickness. These findings reveal a spin depolarization source in the MoS2-based spin valves, thus pointing to possible solut…
The impact of temperature on electrical properties of polymer-based nanocomposites
2020
This work was supported by National Research Foundation of Ukraine, project 2020.02/0217. IK would also like to thank VIAA, State Education Development Agency for Latvian state fellowship. HK would like to thank Ministry of Education and Science of Ukraine, project for young researchers No. 0119U100435. In addition, SP and AAP are thankful for financial support from Latvian Council of Science via grant lzp-2018/2-0083. HK and AAP are grateful for the support from the COST Action CA17126.
Study of the Chemical Conversion of Aluminum Alloys by Coupling CFDE and EQCM
2004
The ability of the channel flow double electrode (CFDE) technique and electrochemical quartz crystal microbalance (EQCM) for studying in situ chromate phosphate conversion coating on 5182 aluminum alloys was explored. It was first demonstrated that aqueous Cr(VI) can be analyzed quantitatively with the CFDE technique by reduction into Cr(III) on a graphite electrode. Samples used for EQCM were quartz plated by physical vapor deposition using a 5182 alloy target, allowing thin layers of aluminum alloys with a similar chemical composition to be obtained. EQCM was adapted in order to account for the hydrodynamic conditions in an industrial process, by placing the quartz in a flow cell. In orde…
Depth selective Mössbauer spectroscopy: Analysis and simulation of 6.4 keV and 14.4 keV spectra obtained from rocks at Gusev Crater, Mars, and layere…
2008
[1] The miniaturized Mossbauer spectrometer (MIMOS) II Mossbauer spectrometers on the Mars Exploration Rovers (MER) simultaneously obtained 6.4 keV and 14.4 keV Mossbauer spectra from rock and soil targets. Because photons with lower energy have a shallower penetration depth, 6.4 keV spectra contain more mineralogical information about the near-surface region of a sample than do 14.4 keV spectra. The influence of surface layers of varying composition and thickness on Mossbauer spectra was investigated by Monte Carlo simulation and by measurement using a copy of the MER MIMOS II instrument and samples with one or two layers of known thicknesses. Thin sections of minerals or metallic Fe foil …
Evaluation of the bending behaviour of laminated glass beams via electronic speckle pattern interferometry
2017
The paper is devoted to the experimental analysis of the kinematical and mechanical behaviour of laminated glass beam structures. In particular, the utilized laminated glass specimens are composed of two glass layers bonded by a polymer layer constituted by Ethylene-vinyl acetate whose thickness has been nominally considered as constant for all the specimens. The experimental behaviour of the analyzed specimens is deduced by applying Electronic Speckle- Pattern Interferometry technique; actually, among optical methods this technique (handled by phase-stepping technique) is very effective to obtain a full-field displacement map and to numerically achieve the longitudinal strain. In particula…
Structural and Chemical Characterization of Cerium Oxide Thin Layers Grown on Silicon Substrate
2015
In this study, we report transmission electron microscopy and electron energy loss spectroscopy study of cerium oxide thin layers deposited on silicon substrate. Transmission electron microscopy experiments have revealed the flat morphology of the deposited layers. In addition, studies of high resolution images have indicated the presence of mainly ceria crystallized nanoparticles. Energy electron loss spectroscopy measurements were also performed in scanning mode to study the evolution of the cerium valence. In addition to Ce4+ inside the layer, the presence of amorphous cerium silicate with valence +3 is pointed out at the vicinity of the substrate.
Optical and dielectric properties of MoO 3 nanosheets for van der Waals heterostructures
2021
Two-dimensional (2D) insulators are a key element in the design and fabrication of van der Waals heterostructures. They are vital as transparent dielectric spacers whose thickness can influence both the photonic, electronic, and optoelectronic properties of 2D devices. Simultaneously, they provide protection of the active layers in the heterostructure. For these critical roles, hexagonal Boron Nitride (hBN) is the dominant choice due to its large bandgap, atomic flatness, low defect density, and encapsulation properties. However, the broad catalogue of 2D insulators offers exciting opportunities to replace hBN in certain applications that require transparent thin layers with additional opti…
Finite element modelling of temperature distribution in the cutting zone in turning processes with differently coated tools
2005
Abstract The aim of this study is to check the applicability of various simulation models to obtain finite element solutions of cutting forces, specific cutting energy and adequate temperatures for a range of coated tool materials and defined cutting conditions. Commercial explicit finite element code Thirdwave AdvantEdge has been used in simulations of orthogonal cutting processes performed by means of uncoated carbide and coated tools. The latter were equipped with progressively increasing number of thin layers including TiC, TiN and Al 2 O 3 films deposited onto ISO P20 carbide substrates. Results showing the tool–chip interfacial friction influencing the temperature distribution fields,…
Investigation of amorphous oxide film-electrolyte junctions by AC techniques
1992
Current AC (alternating current) techniques are used often to characterize the energetics at a semiconducting solid phase/electrolyte interface. For thin layers having a strongly disordered or amorphous structure (such as oxide-passive layers anodically grown on valve metals), interpretative models currently used for crystalline semiconductors may produce misleading data. A new interpretation of the admittance data, based on recent models for amorphous semiconductors (a-Sc) Schottky barriers, is presented for passive films of Nb, W and Ti. The physical bases of the model are presented as well as its advantages and disadvantages. The new theory views the solid/electrolyte interface more sati…
Mechanical properties and microstructural study of homogeneous and heterogeneous laser welds in α, β,and α + β titanium alloys
2018
International audience; Heterogeneous welding has been investigated for three different couples of titanium alloys: α/α + β, α/β,andα + β/β. Plates of 100 × 60 mm and 1.6 or 1.8 mm thick were welded with a Yb:YAG laser. Tensile tests show that the resistance of the heterogeneous welded specimens was generally controlled by those of the weakest material except for the α + β/β where the ultimate tensile strength was approximately equal to the average value of both materials. In every case, the elongation of the welded sample was found to be smaller than that of the base metals. The rupture generally took place outside the weld metal and was found to be most of the time located in the alloy ha…